| Romy the Cat's
personal site dedicated to advanced audio and evolved music reproduction
techniques
|
|
 |
|
|
|
|
|
I got RX5000 a couple of years ago and never replaced the caps. Does anybody have a service manual or list of capacitors with values? ...
|
|
Hi N-set,Yes I added big cap bank to the second stage cathode. Yes it is possible to use filament power supply for fixed bias like Romy did.But I have a stereo EAR834p with a single filament PS. So, I was afraid that one PS for both channels can caus...
|
|
Hi Romy,I read about EAR834p modifications in number of forums. And I never found any explanation how does RIAA feedback work.Only from you I heard about Miller capacity that used in this RIAA.I tried to do my calculations and as I understand the Mil...
|
|
Hi Paul,My question was of cause about my phonostage based on EAR834p and "End Of Live" modification with air capacitors and LCLC + 0A2 power supply.A couple weeks before I increase the second stage ECC83 cathode capacitor value to 43400uF (Kaisei no...
|
|
Hi Guys,The output impedance of ECC83 in cathode follower is around 625 Oms. But 1uF capacitor makes output impedance very big on low frequencies (around 8K Ohm at 20Hz). And in this schematics the global feedback doesn't work at low frequencies. So ...
|
|
Do you use input 50KOhm Z-foil resistor between input tube greed and GND?Does Z-foil sound colder compared to Dale RN60D?U used Dale before. Now I use Shinkoh tantalum resistor. It has similar to Dale tonal balance but sounds smoother.I heard a lot o...
|
|
Hi N-set,Thank you for information.What kind and producer of capacitors do you use?Regards,Alex. ...
|
|
Hi,I have the phonostage with the similar schematics that Romy has.The power supply use SiC Schottky diodes in bridge and 15H choke load exactly like on the scheme in this thread.Is it possible to bypass each Schottky diode by 10-100 pF capacitor?Doe...
|
|
Hi Amir. Thank you for your replay. I tried a different route and it worked this time. I will send you an email using the email address on that site....
|
|
Amir, I tried to access your weblog on your profile www.hifi.ir . It does not seem to work. Is the weblog still active?
Best regards
Alex
...
|
|
Post #20:
..
|
by
alex
on
2015-10-13
|
|
|
[quote user="Romy the Cat"]
alex wrote:Sorry Romy,We are
talking about pivoted tonearm with overhang. That is the geometry that
creates force to pull the cartridge toward the centre of the record. If
you take a moment to observe how anti-scat...
|
|
|
Post #18:
.
|
by
alex
on
2015-10-13
|
|
|
[quote user="Romy the Cat"] be wrote:Your circumference force is right, but when viewed from
above it work clocwise around the lateral bearing of the arm, therefore the arm
wil tend to move inwards :-)Soory, Be, no matter how I
look into it I can’...
|
|
Does anybody try to change shunt regulators OA2 to 15K Ohm resistor?I heard from number of people that OA2 is too noisy for phonostage.For example, in this article wrote about this http://www.audionote.co.uk/articles/tweak_ai_p2_phono_mod_0...
|
|
What about filament?Is the filament ground connected to the common ground?Is the filament ripple is small?...
|
This is my ECC83 Amperex picture.
|
I tried Amperex ECC83 "Bugle Boy". They sounded bad in the EAR RIAA. I like more modern Amperex ECC83, Holland made with orange-red prints....
|
|
Romy,Thank you.I think I should to give some break-in time to Sylvania 0a2.50 hours is enough? Previously I used in my EAR the next set of tubes ECC83: 1-Amperex (red print), 2-Amperex (red print), 3-Sylvania 7025 (yellow print).When I built "End of ...
|
|
Hello Romy,What brand of 0A2 do you use in your phonostage?I used RCA, but after 1.5 years of work it began to spark when phonostage is switched on.I tried Siemens, Mazda and now Sylvania 0A2.Siemens has "disco sound", without mids, just metallic hig...
|
|
Music at Court of St Petersburg
http://www.amazon.com/Music-Court-St-Petersburg-Glinka/dp/B000005W5A/ref=sr_1_4?ie=UTF8&s=music&qid=1284388007&sr=1-4
...
|
|
Romy,I have rebuilt my phonostage (the pictures after update are added to Picasa):1. Fixed filament. Now a ripple about 1mV (unmeasured by my Fluke). The filter is: C-L-C-L-C
30000uf-3mH-30000uf-3mH-30000uf. I put two 3mH chokes & Nichico...
|
|
Romy,Yes, I measured my cartridge-tonearm combination with test disk. The resonant frequency was completely different compared to calculation with http://www.mh-audio.nl/MySystem/RF.asp.7 years ago, I tried Fidelity
Research FR-64FX with Grado Sona...
|
|
Romy,I use Ortofon Rondo Bronze with Nottingham Spacearm and Spacedeck. I hate Spacearm because bad tracking. Also, I can't add mass to Spacearm.I going to try a heavy tonearm.Fidelity Research FR-64FX with Ortofon Rondo Bronze (compliance is 15mm/uN...
|
|
Romy,I used second tube grid resistor, 1.8Meg Holco. (I couldn't find 2 Meg chip and good quality resistor: Dell RN60D or Holco or even Caddock MK-132.)But I felt the deep bus was cut. I tried 1.8Meg Holco & Riken 220K in serial. The deep bus inc...
|
|
Romy,I try to remove the step-up transformers & short the
input grid, the hum has gone.Than, I did next changes:1. Twisted wire from input RCA to step-up transformers. Connect transformers input & output ground directly (not thought ground ...
|
|
Romy,I tried before to cover transformers by foil sheet, it didn't help. Now I try “disconnecting
trick”. The hum was disappeared after phonostage had switched off, while music continued to play.The filament ripple is 32m Volt (5% from DC level). I...
|
|
Hello Romy,I just have build the postage used your "End of Live" scheme and Altec step-up transformers.http://picasaweb.google.com/alex.berger73/Phonostage#I have original EAR. After of 100 hours of working, the new Phonostage sounds more dynamic, ...
|
|
Your point is well taken.Alexd...
|
|
Hello, I agree with you,there is a lot of risk involved in it.However we do have an in home trial program.You simply pay for the unit and shipping, we will send you our DAC. You can listen to it in your own setup, if not completely delighted, return ...
|
|
Well, the issue you are talking about is very complex. You have many components in your signal chain, that contribute to the noise and signal quality,not only in power supply,but also in the signal chain ckts. The USB A/D converters have their own po...
|
|
Hello, I must say you did not listen to NOS DAC properly designed.Most of the NOS DACs on the market are following minimalist concepts.Meaning, they merely are just a combination of SPDIF receiver chip and DAC chip itself.While this approach is worki...
|
|
|
|
|
All context of this site except the Forum's posts
Copyright © Roman Bessnow 2004-2025
All messages within the Site’s Forum Copyright © by
authors of the posts
|
|
Last 24-hours posts: |
0 |
|
 |
|
|
Total human visitors: |
53,610,595 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Franceschini, Petronio (9 »
|
|
Campra, André (4 Dece»
|
|
Halvorsen, Johan (15 March»
|
|
Harty, Herbert Hamilton (4»
|
|
Appeldoorn, Christina (Din»
|
|
Britten, Benjamin (22 Nove»
|
|
Zappa, Frank (21 December »
|
|
Hannah, Ron (4 December 19»
|
|
Even, Pierre (4 December 1»
|
|
LaFave, Kenneth (4 Decembe»
|
|
Popoff, Ross (4 December 1»
|
|
|
|
|
|
|