| Search | Login/Register
   Home » Analog Playback» Micro RX 5000 (10 posts, 1 page)
  Print Thread | 1st Post |  
Page 1 of 1 (10 items) Select Pages: 
   Target    Threads for related reading   Most recent post in related threads   Forum  Replies   Views   Started 
  »  New  Micro Seiki Armboards: Is bigger actually better?..  The Micro Seiki Armboards...  Analog Playback Forum     1  30346  07-29-2010
  »  New  RX-5000 Thread tension...  You use wrong methodological logic...  Analog Playback Forum     3  40205  10-24-2010
  »  New  Copper Mat on a Micro Seiki Gun Metal Platter..  Size of ceramic ball...  Analog Playback Forum     122  414472  10-07-2015
11-09-2008 Post does not mapped to Knowledge Tree
pokie
Posts 3
Joined on 11-09-2008
Post #: 1
Post ID: 8780
Reply to: 8780
Micro RX 5000
fiogf49gjkf0d

Hi,

I've just got RX 5000 from my uncle, but don't really know how to remove platter form its frame. I've made handels to put in 2 provided screws on platter but I still can't remove. Does anyone help me this?

Rgds,

Pok

11-09-2008 Post does not mapped to Knowledge Tree
RonyWeissman
Lyon, France
Posts 138
Joined on 05-29-2004
Post #: 2
Post ID: 8786
Reply to: 8780
RX 5000 lifting
fiogf49gjkf0d
Hi, if it's like mine you have to pull up very hard and it slides off. spray some lubricant in there maybe at first?

R weissman
11-09-2008 Post does not mapped to Knowledge Tree
Romy the Cat


Boston, MA
Posts 10,159
Joined on 05-28-2004
Post #: 3
Post ID: 8797
Reply to: 8780
The old Micro Seiki
fiogf49gjkf0d
Yes, I had 4 Micros 5000 and one of them was almost glued platter. You need to flip it upside down and hit with a small hammer to knock to the TT’s back, in the bearing. It will eventually slide out. To service Micro Seiki 5000 is kind of tricky… I do not remember exactly by you might need to unscrew the center peace in this TT, it is depends of what kind platter you get with your 5000 .The Cat

"I wish I could score everything for horns." - Richard Wagner. "Our writing equipment takes part in the forming of our thoughts." - Friedrich Nietzsche
11-10-2008 Post does not mapped to Knowledge Tree
pokie
Posts 3
Joined on 11-09-2008
Post #: 4
Post ID: 8799
Reply to: 8797
RX5000
fiogf49gjkf0d
Many thanks,   I don't really what version my platter is.  Could you tell me from this pic?


I removed the Thorens mat so it now looks so disgusting.
11-10-2008 Post does not mapped to Knowledge Tree
Romy the Cat


Boston, MA
Posts 10,159
Joined on 05-28-2004
Post #: 5
Post ID: 8800
Reply to: 8799
It is not that I care, but you’ll be fine.
fiogf49gjkf0d
I see, it is the simple one. There is nothing that holds this platter. Flip it and “shake” it. If it is not working then throw the TT in a freezer of a half of day, then take it off and heat with blowtorch-like devise the bottom bearing. It is extreme measure and you shell be able to take it off without it.

"I wish I could score everything for horns." - Richard Wagner. "Our writing equipment takes part in the forming of our thoughts." - Friedrich Nietzsche
11-13-2008 Post does not mapped to Knowledge Tree
pokie
Posts 3
Joined on 11-09-2008
Post #: 6
Post ID: 8847
Reply to: 8800
Earth it
fiogf49gjkf0d
I manged to split the platter off already  ( take the whole bearing with the platter, up side down on the thick card board and hit it, nothing harms the bearing). Now I would like to earth the bearing but I can't see anywhere I can hook.  Can anyone advise me this? 

Thanks
11-13-2008 Post does not mapped to Knowledge Tree
Romy the Cat


Boston, MA
Posts 10,159
Joined on 05-28-2004
Post #: 7
Post ID: 8848
Reply to: 8847
The Micro Seiki autopsy
fiogf49gjkf0d
Sorry, I do not follow you. If I remember correctly the regular, non-air-bearing Micro 5000 has a few inches long cylinder that is sitting in a shaft that serves as a horizontal bearing. For virtual bearing they use a small metal ball under the bottom that pressed by the bearing cover (with very badly made pressure plate that always is warn in old TT and need to be replaced). You stick the cylinder from under the bottom, press the bottom plate and then hang the platter on the other side. It is very simple. I do not know what “split the platter” would mean. If you removed it from the cylinder then what would mean the “earth the bearing”? Just unscrew 4 screws from the bottom and the cylinder and bearing will fall out. If you unscrew the screws but the bearing does not go then hit recursively the tip of the cylinder and the bottom plate with light hummer and they will go off. There is nothing that holds it the cylinder in there. Do not be overly zealous with hammering. In this TT you will not damage it but if your TT was not oiled for 30 years that you do not what to scratch the external sides of the cylinder and internal sides of the shaft.

"I wish I could score everything for horns." - Richard Wagner. "Our writing equipment takes part in the forming of our thoughts." - Friedrich Nietzsche
02-04-2016 Post does not mapped to Knowledge Tree
chaslieb
Posts 4
Joined on 01-30-2016
Post #: 8
Post ID: 22463
Reply to: 8848
Somewhat similar question about bearing on 1500
fiogf49gjkf0d
I just acquired a Micro RX-1500. Without the platter on, the bearing unit turns very slowly suggesting a highly viscous oil. The spindle turns freely, but the feel to my fingers is like turning a spoon in honey. It undoubtedly will turn much more freely with a heavy platter on top with a pull on the outside edge. Nevertheless, the age of the table leads me to believe that the oil has gummed up.  

There is a stern warning on the bottom plate of the bearing which says, "Do not remove rear cap of the center shaft. If this warning is not heeded, the oil which is hermetically sealed will escape and this will cause trouble."  [-X  

I fear the wrath of the Micro Seiki label makers and note that the high viscosity can be intentional as it certainly will reduce vibration or wear of metal on metal. Have you tried turning their RX version Seiki spindle without the platter, and is it meant to be so viscous? Has anyone removed the bottom plate and cleaned the spindle or replaced the oil?  What type of oil is supposed to be used?

This deck has the vacuum plate so the viscosity may also prevent the oil from running into the vacuum ports. Any one with a heavy platter Micro with a non-air bearing is asked to put in their experiences.

Thanks,

Charles
02-04-2016 Post does not mapped to Knowledge Tree
Romy the Cat


Boston, MA
Posts 10,159
Joined on 05-28-2004
Post #: 9
Post ID: 22464
Reply to: 22463
Do not worry.
fiogf49gjkf0d
Charles, do not worry, discard the warning. There is many bolts iron plate at the bottom. You need to open up, clean up the old used up and solidified oil and put new one. Do not ask what one to use - no one know. Oil today is 10000 time better then it was 40 years back, you will use your own sense and to get the one you like. With a good oil and healthy bearing you should get ~ 3min of platter rotation after you get 33 RPM and take belt off. One more thing to watch. At the bottom of the shaft it will be a single ball mounted above a small steel plate. This small steel plate is removable. Inspect it as confirm that after the years of bad-oil rotation the ball did not make indentation in this small steel plate. If it goes them replace it, perhaps with porcelain or whatever makes you happy.

"I wish I could score everything for horns." - Richard Wagner. "Our writing equipment takes part in the forming of our thoughts." - Friedrich Nietzsche
07-07-2022 Post does not mapped to Knowledge Tree
rom661
Kansas City
Posts 10
Joined on 04-03-2022
Post #: 10
Post ID: 26830
Reply to: 8800
Alternative method
I was convinced mine wouldn't come off.  It did.  Inserted long screws, had one person pulling up on them while I worked three wood shims around the sides, slowing pushing it up. After 1/8" or so it popped free.

Richard Milam
Page 1 of 1 (10 items) Select Pages: 
   Target    Threads for related reading   Most recent post in related threads   Forum  Replies   Views   Started 
  »  New  Micro Seiki Armboards: Is bigger actually better?..  The Micro Seiki Armboards...  Analog Playback Forum     1  30346  07-29-2010
  »  New  RX-5000 Thread tension...  You use wrong methodological logic...  Analog Playback Forum     3  40205  10-24-2010
  »  New  Copper Mat on a Micro Seiki Gun Metal Platter..  Size of ceramic ball...  Analog Playback Forum     122  414472  10-07-2015
Home Page  |  Last 24Hours  | Search  |  SiteMap  | Questions or Problems | Copyright Note
The content of all messages within the Forums Copyright © by authors of the posts