Rerurn to Romy the Cat's Site

Didital Things
Topic: Splitters, preamps, etc

Page 1 of 1 (6 items)


Posted by Alex Yakovlev on 06-01-2005

cialis cena

cialis
I need to add another output to my BiDat and I was wondering if there is anything special that I have to do. I really don't want to send it to John for three months just to be able to add another output for headphone amplifier.
Thank you.

Posted by Chirag on 06-01-2005

mirtazapine 30 mg street price

buy mirtazapine

viagra cena

viagra

abortion pill online review

cheap abortion pill
Hey Alex,

Aside from the obvious swapping of cables, do you have any extra outputs in your preamp?  Don't try any sort of splitting device...I did it once with very cheap cables and couldn't listen for more than 30 seconds.  You could always pull another signal from the other output jacks and drill the holes yourself (paying attention to grounding etc)...the impedence issues shouldn't be much of an issue.

On another note, aside from the general idiocy of poorly aimed audio technologies, what makes Bidat so non-reproducible these days?  Are there any patents on this thing that prevent John Wright from just producing some bidats?  The board inside is puny (old chips?), the power supply is nothing special and the output stage is opamps....this did sell for only 1k back in the day...its not much in parts.  Don't get me wrong, I love my Bidats and no way will I sell them or take one apart to play with (I tried once and got scared).  I just wonder if some of the slight upper range grainy hardness (transport?? cabling??) can be removed with better supplies or output stage.

Best,
Chirag

Posted by Romy the Cat on 06-02-2005

 Chirag wrote:
I just wonder if some of the slight upper range grainy hardness (transport?? cabling??) can be removed with better supplies or output stage.
Yes, Chirag.

It is transport, cabling, amplifiers, tweeters, electricity or whatever it might be. What Bidat certainly does not have is the “upper range grainy hardness”. In fact, Bidat might be use as an indictor to highlight that any other DAC (among those that I've seen with a minor exception of one) do have the various degrees of  the “upper range grainy hardness”.

Rgs,
The Cat


Posted by Chirag on 06-02-2005

nix new york

nix 22 forskning.website nix jewelry
Hi Romy,

Bidat IS quite a bit better than any dac i've used in that upper range (or any where else), but there is a bit of hardness there that I have problems killing off in my system.  Its not possibly enough to motivate me to do actively do something, but the Alex post got me thinking about it.  I did have success getting rid of it with a filterless dac (smoothing distortions), but there were at least 15 other identifiable problems with that thing anyway...what a waste of energy and time.

Best,
Chirag

Posted by Alex Yakovlev on 06-02-2005

prednisolon kur

prednisolon

benadryl pregnancy second trimester

benadryl pregnancy click
Chirag, my amplifier is passive pre and tube power, with input selector relay-based, and with no pre-out so there is unfortunately no easy way for me to utilize it for my purposes. My initial idea was to do just that, but then I would have to keep it on at all times when I listen to my headphones. Besides, there is no available space on the back panel for pre-out.
I checked with John, he said there should be no problem just adding another output as long as I am not driving low impedance load with it.

Posted by Chirag on 06-03-2005

citalopram hydrobromide and alcohol

citalopram and alcohol
Hi Alex,

Short of waving goodbye to the Bidat for a few months, you could always TRY the splitter idea from your favorite cable guy.  It may be acceptable enough for your needs.

Did you mean there is no space on the back of your passive/relay based pre?  Is it a Placette...can the Guy do something about this?  I've seen custom inputs/outputs on some of his toys.

Sorry I can't offer more suggestions...but you can always spend a zillion dollars to pick up another bidat and transport.

Best,
Chirag

Page 1 of 1 (6 items)